A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

天基轻气炮发射清除低轨碎片方案及关键技术分析

文章分析了现有的空间碎片清除方式,并以800~1200 km低地球轨道高度上1~10 cm量级的空间碎片为清除目标,提出了天基轻气炮清除碎片的新方法。首先分析了轻气炮有效载荷在典型参数下的弹丸加速能力;之后根据将碎片降轨使其坠入大气层烧毁的设想,提出天基轻气炮共面清除碎片的方式,并选择轨道高度800 km的圆轨道作为碎片运行轨道进行可行性分析。计算表明,对半径10 cm、厚度1 cm的铝合金圆板碎片(质量211.95 g),使用初速1 km/s、重10 g的黏性弹丸可按任务方案达到清除效果。此外,计算出该参数弹丸对轨道高度800~1200 km的圆轨道上可清除的最大碎片质量为500~825 g,证明轻气炮弹丸对1~10 cm的碎片具有较强的清除能力。最后,分析了以轻气炮为有效载荷的航天器在完成清除碎片任务时的关键技术。     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

Availability modeling for periodically inspection system with different lifetime and repair-time distribution

Availability is a main feature of design and operation of all engineering system. Recently,availability evaluation of periodical inspection systems with different structures is at the center of attention due to the wide application in engineering. In this paper, an analytical and probabilistic availability model for periodical inspection system is proposed by a new recursively algorithm,which can achieve limiting average availability and instantaneous availability of periodical inspection system under arbitrary lifetime and repair-time distributions. Then three application examples are presented, the systems lifetime and repair-time are respectively fellow exponential/exponential,Weibull/normal and Weibull/lognormal distribution. Finally, a Weibull/lognormal system is studied to analyze the dynamic relationship between inspection period and availability. The results indicate that the proposed approach can provide the technology support for improving system availability and determining reasonable inspection period.     

基于自适应容积粒子滤波的车辆状态估计

针对车辆状态估计中由模型的强非线性、噪声的非高斯分布等相关因素导致估计精度下降甚至发散的问题,本文提出了基于自适应容积粒子滤波(Adaptive cubature particle filter,ACPF)的车辆状态估计器。首先基于非稳态动态轮胎模型,构建高维度非线性八自由度车辆模型。其次利用自适应容积卡尔曼滤波(Adaptive cubature Kalman filter,ACKF)算法更新基本粒子滤波(Particle filter,PF)算法的重要性密度函数,以完成自适应容积粒子滤波算法设计。利用车载传感器信息,运用ACPF算法实现对车辆的侧倾角、质心侧偏角等关键状态变量高精度在线观测。搭建Simulink-Carsim联合仿真平台进行了算法的验证,结果表明该算法状态估计精度高于传统无迹粒子滤波(Unscented particle filter,UPF)算法,且算法运算效率高于UPF算法,而传统PF估计值发散。研究结果为实现车辆动力学精准控制提供了理论支持。     

A general calculation method to specify center-of-buoyancy for the stratospheric airship with multiple gas cells

As the lighter-than-air (LTA) flight vehicle, the stratospheric airship is a desirable platform to provide communication and surveillance services. During the ascent from sea-level to the mission altitude, the volume of the lifting gas may change significantly, which will result in the change of the center-of-buoyancy (CB). A general calculation method is developed to specify CB for the stratospheric airship with a double-ellipsoid hull and an arbitrary number of the gas cells. The cross-section-integral (CSI) method is used as a basic calculation scenario to specify CB. Considering the complexity in determining the boundary between the helium and air in the gas cell, a searching algorithm is put forward and the specification of CB can be conducted by the iterative calculation. As an important application, the stable condition of the pitch angle is analyzed when the change of CB is involved. Under different initial configurations, the stable pitch angle of the stratospheric airship during the ascent is specified and compared, which shows the advantages of the multi-gas-cell configuration. The results of this paper may provide an important reference for the engineering application of the stratospheric airship.     

吸气式电推进系统可行条件分析

吸气式电推进系统作为有可能实现长寿命超低轨飞行的技术而被关注。根据不同轨道环境条件，采用管状结构进气道、以及机械增压的吸气方式，讨论了吸气式电推进系统所需的可行条件。分析表明，在轨高度180~240km，航天器所需总功耗与迎风面之比需要大于2kW/m2，电推力器比冲需大于4×104m/s，方可满足推阻平衡需求。分析得出，实现吸气式系统在地球轨道的运用，关键技术在于增加气体收集效率并且降低收集功耗，同时电推力器的效率还需进一步提升。     

多种工质下螺旋波等离子体源波场结构数值模拟

针对螺旋波等离子体放电机理，开展了多种工质条件下的螺旋波放电等离子体内波场结构数值模拟研究。计算发现:氦气等离子体的Er分量在径向边界处的峰值更为突出，有利于等离子体在径向的输运，波电场径向分量决定了电流密度径向分量在内部的表现。在0.266 Pa和1.064 Pa两种气体压强条件下，通过波场结构验证了气压对于波阻尼影响的结论。波场结构是螺旋波在等离子体内传播以及能量沉积的微观体现，研究螺旋波波场结构是揭示其高电离效率的重要途径。初步探索了功率耦合机制，为实验系统优化及实验方案设定奠定理论基础。     

低轨天基信息定向分发区域分割编码控制方法

为提高低轨指向性信息分发链路的频谱利用效率，从天基分发平台与地面用户的相对位置关系入手，建立了分发指向、编码增益与信道传输容量的量化关系。在此基础上，提出一种低轨天基信息定向分发区域分割编码控制方法，该方法针对不同信息分发区域，采用最小均方误差(MMSE)作为区域分割准则选择编码方式，既提升了信道传输效率也便于工程实现。最后，本文通过仿真分析了方法的效能和性能影响因素，并与现有自适应编码方法进行了对比，验证了本方法的有效性和可靠性。     

三维叶轮机叶片黏性反问题设计改进方法

提出了一种改进的适用于三维黏性流场的叶轮机叶片反问题设计方法。该方法假设叶片的中弧线具有虚拟移动速度,其位移量由目标载荷与实际载荷的差值计算,并利用黏性底层厚度进行限制。采用三次B样条曲线插值方法对叶片中弧线进行光顺,新叶型通过更新后的中弧线和给定的叶片厚度得到。算例验算结果表明:该方法能够根据设计意图对叶型进行修改,鲁棒性强,收敛速度快,叶片的可变自由度高,不依赖于特定的网格和求解器,具备一定的通用性。